In such case the drive usually spins up fine, it doesn’t click but has one of the following symptoms: Usually this occurs after a fall and the drive either doesn’t spin up at all with a siren sound: Main part of firmware is stored on the platters in so-called Service Area. This complex and precise procedure requires a lot of experience and use of specialized hardware to maintain platters in perfect alignment. If you hear your Western Digital hard drive making some other unusual noises visit our Hard Drive Sounds page for more examples.

Uploader: Kigataur
Date Added: 11 February 2005
File Size: 37.95 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 48151
Price: Free* [*Free Regsitration Required]

Don’t try to open the drive by yourself – you could damage the platters making your data unrecoverable. Usually this occurs after a fall and the drive either doesn’t spin up at all with a wdc wd800bb-00jhc0 sound: Heads wdc wd800bb-00jhc0 normally wddc on the parking ramp outside of the platters, but sometimes after a fall or abnormal termination they fail to return to their regular parking position and are left on the surface.

It no longer spins or powers up.

All Western Wdc wd800bb-00jhc0 hard drives are also well-known for their firmware problems. Don’t attempt to open the drive by yourself – you will damage wsc platters and this will make your data unrecoverable.

In as clean environment as possible home isolated glove box inspected surface of platters, no apparent damage. The 4th one survived for several days but when I went wdc wd800bb-00jhc0 back it up, it to failed. When the drive starts reading data from such unreadable bad sector it wdc wd800bb-00jhc0 start freezing, scratching wd800bv-00jhc0 sometimes even clicking: Drive spins up normal for 5 seconds, then starts rhythmic clicking, like a metronome with alternating beats. We have seen a number of websites lately cloning information from our wdc wd800bb-00jhc0.

This is how bad sectors appear. Quite often bad power supply unit combined with power streak is usually enough to fry spindle driver chip on the electronics and make wdc wd800bb-00jhc0 data inaccessible.

Western Digital WD800BB-00JHC0 Data Recovery Information

That’s usually the only way to retrieve as much wdc wd800bb-00jhc0 as possible from such sectors. This complex and precise procedure requires a lot of experience and use of specialized hardware to maintain platters in perfect alignment. Data recovery in such case involves removing platters from the hard drive in clean room environment and putting them wdc wd800bb-00jhc0 matching donor.

Immediately after the motor stops spinning they wdc wd800bb-00jhc0 to the ideally smooth surface and it becomes impossible to wdc wd800bb-00jhc0 them without proper tools and experience. Wwdc such case the drive usually spins up fine, it doesn’t click but has one of the following symptoms: Firmware of the drive is not located on the logic board as most people think.

The problem is that logic board on modern hard drive is adapted to the head disk wd800bb-00hc0 it was manufactured with. In our lab we use specialized software and hardware wdc wd800bb-00jhc0 rebuild these parameters or transfer them from fried board to make donor PCB fully compatible with damaged drive. We see mostly failed drives in our lab and therefore we don’t have complete statistics.

The drive does not power up. In wdc wd800bb-00jhc0 lab we use special imaging hardware tools that are capable of reading raw sector data ignoring low level checksum check. Any further reading attempts would just add up to the problems and could make your data unrecoverable.

Insert system disk and press enter”, “Hard wdc wd800bb-00jhc0 not recognized”, “Drive Mount Failure” or some other hard drive boot error.

Western Digital Caviar WDBB

WD drives are very vulnerable to overheating, power surges and streaks. All this leads to further damage to the surface, heads and causes more data loss. wdc wd800bb-00jhc0

One of them is heads sticktion wdc wd800bb-00jhc0 the platter surface. It is quite a complicated job and requires use of specialized expensive equipment and deep knowledge of hard drive design and data recovery technology to repair the firmware. I was hoping to use the PCB board to repair the the other 3. At the moment wdc wd800bb-00jhc0 is not possible to fix this kind of problem at home.

They can steal information but they can’t steal knowledge wdc wd800bb-00jhc0 experience. The drive fell while mounted in a chassis. Capable But Command Failed” or “Disk boot failure.